manualshive.com logo in svg

Rohde & Schwarz 1157.3458.02, Operating Manual, Page: 60 / 80

Share
Download
Rohde & Schwarz 1157.3458.02 Operating Manual Download Page 60

Command Description 

R&S FSH-K1  

1157.3564.12 54 

E-8 

Occupied Bandwidth 

Command 

Parameters 

Unit 

Comment 

OBW 

<numeric value> 

 

GET command only 

OBWSTD 0…3 

 

 

OBWCSTD <string> 

  

OBWCHBW <numeric 

value> 

Hz 

 

LVLADJUST 

 

 

CMD command only 

OBW (Occupied Bandwidth) 

This command queries the measured occupied bandwidth. 

Example: 

get<cr>

 

0<cr>

 

obw<cr>

 

‘query power level from sensor 

 

0<cr>

 

‘responds parameter ok 

 

-22E6<cr>

 ‘response: 

occupied 

bandwidth 

 

OBWSTD (Occupied Bandwidth Standard) 

This command defines the standard used for the occupied bandwidth measurement. 
 

Value 

Occupied Bandwidth Standard 

0

User 

1

3GPP WCDMA 

2

cdmaOne 

3

cdma2000 1x 

Example: 

set<cr>

 

0<cr>

 

obwstd,1<cr>

 

‘select 3GPP WCDMA as standard 

 

0<cr>

 

‘responds parameter ok 

 

Note:  If any customized standard was previously selected a value of ‘4’ will be returned as a response 

to a GET OBWSTD query. 

 

OBWCSTD (Occupied Bandwidth Customized Standard) 

This command selects the customized standard for the occupied bandwidth measurement previously 
loaded with R&S FSHView software. 

Example: 

set<cr>

 

0<cr>

 

obwcstd,MyStd<cr>

 ‘select 

MyStd 

as 

standard 

 

0<cr>

 

‘responds parameter ok 

 

Summary of Contents for 1157.3458.02

















































































Reviews:

No comments