manualshive.com logo in svg

Rohde & Schwarz 1157.3458.02, Operating Manual, Page: 51 / 80

Share
Download
Rohde & Schwarz 1157.3458.02 Operating Manual Download Page 51

R&S FSH-K1 

Command Description  

1157.3564.12 45 

E-8 

LIMCHKREMOTE (Limit Check Remote Message) 

This command enables the remote message (frequency/c level) on limit check and/or on 
threshold limit fail. The instrument will send a message (frequency/channel and level) every time the 
limit is exceeded. 
 

Value 

Limit Check Remote 

0

OFF 

1

Limit Check – Remote message on 
fail 

Example: 

get<cr>

 

0<cr>

 

limchkremote,1<cr>

 

‘enable remote massage on limit fail 

 

0<cr>

 

‘responds parameter ok 

 

123.456E6,23.5<cr>

 ‘limit 

exceeded 

 

130.567E6,22.0<cr>

 ‘limit 

exceeded….. 

 

…

0<cr>

 

‘remote message on limit fail OFF 

 

THRLOW (Lower Threshold Line) 

This command defines the lower threshold line (value). The unit of the threshold value is specified with 
the Unit parameter. This command is available in Receiver / Scan Mode only. 

Example:

 

set<cr>

 

0<cr>

 

thrlow,30<cr>

 

‘specifies lower threshold line to -30 dBuV 

 

0<cr>

 

‘responds parameter ok 

 

THRUPP (Upper Threshold Line) 

This command defines the upper threshold line (value). The unit of the threshold value is specified with 
the Unit parameter. Available in Receiver / Scan Mode only. 

Example:

 

set<cr>

 

0<cr>

 

thrupp,70<cr>

 

‘specifies upper threshold line to 70 dBuV 

 

0<cr>

 

‘responds parameter ok 

 

THRPASS (Threshold Line Passed Query) 

This command returns the threshold line check status. Available in Receiver / Scan Mode only. 
 

Value 

Threshold Line Check 

0

Unkown 

1

Failed 

2

Passed 

Example: 

get<cr>

 

0<cr>

 

thrpass<cr>

 

‘query threshold line check 

 

0<cr>

 

‘responds parameter ok 

 

2

‘threshold check passed 

 

Summary of Contents for 1157.3458.02

















































































Reviews:

No comments