manualshive.com logo in svg

Rohde & Schwarz 1157.3458.02, Operating Manual, Page: 3 / 80

Share
Download
Rohde & Schwarz 1157.3458.02 Operating Manual Download Page 3

R&S FSH-K1 

Table of Contents 

1157.3564.12 I.1 

E-8 

Contents

 

Enabling Remote Control Option R&S FSH-K1

................................................................................1

 

Connecting PCs

...................................................................................................................................2

 

Installation of the driver for the USB optical cable (R&S FSH-Z37) ..............................................2

 

Serial Port Configuration ...............................................................................................................2

 

Notational Conventions

......................................................................................................................3

 

Starting Remote Control Operation ...............................................................................................3

 

Device Messages

.................................................................................................................................4

 

Acknowledge Response <ack> .....................................................................................................4

 

Timeout..........................................................................................................................................4

 

Functional Description of Commands ...........................................................................................5

 

Parameter Overview

............................................................................................................................7

 

Get / Set Parameter.......................................................................................................................7

 

Get Parameter .............................................................................................................................10

 

CMD Commands .........................................................................................................................11

 

Command Description

......................................................................................................................12

 

General Commands ....................................................................................................................12

 

Frequency and Span Settings .....................................................................................................16

 

Amplitude Settings.......................................................................................................................18

 

Bandwidth Settings ......................................................................................................................21

 

Sweep Settings............................................................................................................................24

 

Trace Settings..............................................................................................................................26

 

Marker..........................................................................................................................................32

 

Measurement...............................................................................................................................40

 

Tracking Generator......................................................................................................................46

 

Power Sensor ..............................................................................................................................50

 

Channel Power ............................................................................................................................52

 

Occupied Bandwidth....................................................................................................................54

 

TDMA Power ...............................................................................................................................56

 

Distance To Fault Measurement .................................................................................................58

 

Receiver Mode.............................................................................................................................60

 

Carrier / Noise Measurement ......................................................................................................63

 

WCDMA BTS CDP Measurement ...............................................................................................67

 

Programming Examples

...................................................................................................................72

 

Summary of Contents for 1157.3458.02

















































































Reviews:

No comments