Riester 04045396208797, Instructions For Use Manual

Page: 57 / 184

RBP- 100
Seite 19 von 23
11. Technical Specifications
Operating conditions: 10 -­ 40 °C / 50 -­ 104 °F
15 -­ 95 % relative maximum humidity
Storage conditions: -­20 -­ +55 °C / -­4 -­ +131 °F
15 -­ 95 % relative maximum humidity
Weight: 510g (including batteries)
Dimensions: 170 x 135x 41 mm
Measuring procedure: oscillometric, corresponding to Korotkoff
method: Phase I systolic, Phase V diastolic
Measurement range: 60 -­ 255 mmHg – systolic blood pressure
30 -­ 200 mmHg – diastolic blood pressure
40 -­ 200 beats per minute – pulse
Cuff pressure display range: 0 -­ 299 mmHg
Resolution: 1 mmHg
Static accuracy: pressure within ± 3 mmHg
Pulse accuracy: ± 5 % of the readout value
Voltage source: NiMH Battery pack, 4.8V 2400mAh
Mains adapter DC 7.5V, 1.5 mA
Battery lifetime: approx. 1000 measurements (after the battery
pack is fully charged)
IP Class: IP20
Reference to standards: IEC 60601-­1;;
IEC 60601-­1-­2 (EMC)
DIN EN ISO 81060-­1
IEC 80601-­2-­30
EN 1060-­1 /-­3
12. EMC
Guidance and manufacture’s declaration – electromagnetic emission
The RBP-­100 Blood Pressure Monitor and the RBP-­100 USB Blood Pressure Monitor is intended
for use in the electromagnetic environment specified below. The customer of the user of the RBP-­
100 Blood Pressure Monitor and the RBP-­100 USB Blood Pressure Monitor should assure that it
is used in such an environment.
Emission test Compliance Electromagnetic environment – guidance
RF emissions
CISPR 11
Group 1
The RBP-­100 Blood Pressure Monitor and the
RBP-­100 USB Blood Pressure Monitor RF
energy only for its internal function. Therefore,
its RF emissions are very low and are not
likely to cause any interference in nearby
electronic equipment.
RF emission
CISPR 11
Class B
The RBP-­100 Blood Pressure Monitor and the
RBP-­100 USB Blood Pressure Monitor is
suitable for use in all establishments, other
than domestic and those directly connected to
the public low-­voltage power supply network
that supplies buildings used for domestic
purposes.
Harmonic emissions
IEC 61000-­3-­2
Pass
Voltage fluctuations/
flicker emissions
IEC 61000-­3-­3
Pass
Seite 20 von 23
Guidance and manufacture’s declaration – electromagnetic immunity
The RBP-­100 Blood Pressure Monitor and the RBP-­100 USB Blood Pressure Monitor is intended for use in
the electromagnetic environment specified below. The customer or the user of RBP-­100 Blood Pressure
Monitor and the RBP-­100 USB Blood Pressure Monitor should assure that it is used in such an
environment.
Immunity test IEC 60601 test level Compliance level
Electromagnetic environment -­
guidance
Electrostatic
discharge (ESD)
IEC 61000-­4-­2
Con: ± 8 kV
Air:
±
2,4,8,15 kV
Con: ± 8 kV
Air:
±
2,4,8,15 kV
Floors should be wood, concrete
or ceramic tile. If floor are
covered with synthetic material,
the relative humidity should be at
least 30%.
Electrical fast
transient/burst
IEC 61000-­4-­4
Pass Pass Mains power quality should be
that of a typical commercial or
hospital environment.
Surge
IEC 61000-­4-­5
Pass Pass Mains power quality should be
that of a typical commercial or
hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC 61000-­4-­11
Pass Pass Mains power quality should be
that of a typical commercial or
hospital environment. If the user
of the RBP-­100 Blood Pressure
Monitor and the RBP-­100 USB
Blood Pressure Monitor requires
continued operation during power
mains interruptions, it is
recommended that the RBP-­100
Blood Pressure Monitor and the
RBP-­100 USB Blood Pressure
Monitor be powered from an
uninterruptible power supply or a
battery.
Power frequency
(50Hz/60Hz)
magnetic field IEC
61000-­4-­8
30A/m 30A/m Power frequency magnetic fields
should be at levels characteristic
of a typical location in a typical
commercial or hospital
environment.
NOTE U
T
is the a.c. mains voltage prior to application of the test level.