Ricoh Aficio SP C240DN Page 157 Hardware Manual Download

Page: 157 / 172

Moving the Printer

Moving the printer in a short distance

• Do not remove the print cartridges when moving the printer.

Be sure to check the following points:

• The power switch is turned off.
• The power cable is unplugged from the wall outlet.
• The interface cable is unplugged from the printer.

If Tray 2 is installed, remove it.

Lift the printer with two people by using the inset grips on both sides of the printer, and
then move it horizontally to the place where you want to install it.

CER047

If you have removed Tray 2, reinstall it.

• Be sure to move the printer horizontally. To prevent toner from scattering, move the printer

carefully.

Moving and Transporting the Printer

155

Summary of Contents for Aficio SP C240DN













































































































































































Search results

Summary of Contents for Aficio SP C240DN

Reviews:

Related manuals for Aficio SP C240DN

Brands by name

Popular brands

Ricoh Aficio SP C240DN, Hardware Manual

Search results

Summary of Contents for Aficio SP C240DN

Reviews:

Related manuals for Aficio SP C240DN

Brands by name

Popular brands