manualshive.com logo in svg

Ricoh Aficio SP C240DN, Hardware Manual, Page: 118 / 172

Share
Download
Ricoh Aficio SP C240DN Hardware Manual Download Page 118

Cleaning the Friction Pad and the Paper Feed

Roller

If the friction pad or paper feed roller is dirty, a multi-feed or misfeed might occur. In this case, clean the
friction pad and paper feed roller as follows:

• Unplug the power cord from the wall outlet before you move the machine. While moving the

machine, take care that the power cord is not damaged under the machine. Failing to take
these precautions could result in fire or electric shock.

• Do not pull out the paper tray forcefully. If you do, the tray might fall and cause an injury.

• Do not put your hands inside the printer when the input tray is removed. Some internal parts

become hot and are a burn hazard.

• Do not use chemical cleaner or organic solvent such as thinner or benzine.

1.

Turn off the power switch.

2.

Unplug the power cord from the wall outlet. Remove all the cables from the printer.

3.

Pull out tray 1 carefully with both hands.

CER030

Place the tray on a flat surface. When there is paper in the tray, remove paper.

7. Cleaning the Printer

116

7

Summary of Contents for Aficio SP C240DN













































































































































































Reviews:

No comments