Ricoh Aficio SP C240DN Page 125 Hardware Manual Download

Page: 125 / 172

8. Troubleshooting

This chapter provides solutions to common problems and it also explains how to correct unwanted print
results.

Error & Status Messages on the Control Panel

This section explains what the messages that appear on the control panel mean and what to do when a
particular message appears.

Status messages

Message

Explanation

Recommended Action

Offline

The machine is Offline.

To start printing, switch the
machine to online by pressing
the [Stop/Start] key on the
control panel.

Processing...

The machine is printing.

Wait a while.

Ready

This is the default ready
message.

The machine is ready for use.
No action is required.

Calibrating...

The machine is calibrating.

Wait a while.

Printing...

The machine is printing.

Wait a while.

Please wait

The machine is waiting for the
next data to print.

Wait a while.

Warming up...

The printer is warming up or
toner is being supplied.

Wait until "Ready" appears on
the display.

Messages

Message

Explanation

Recommended Action

Size Msmtch: # Start/JobReset

The paper size setting in the tray
# (1, 2, bypass) differs from
that of actual paper size in the
tray.

Load paper of the selected size
in the tray, and then press the
[Stop/Start] key to continue
printing.
Press the [Job Reset] key to
cancel printing.

123

Summary of Contents for Aficio SP C240DN













































































































































































Search results

Summary of Contents for Aficio SP C240DN

Reviews:

Related manuals for Aficio SP C240DN

Brands by name

Popular brands

Ricoh Aficio SP C240DN, Hardware Manual

Search results

Summary of Contents for Aficio SP C240DN

Reviews:

Related manuals for Aficio SP C240DN

Brands by name

Popular brands