manualshive.com logo in svg

Ricoh Aficio SP C240DN, Hardware Manual, Page: 128 / 172

Share
Download
Ricoh Aficio SP C240DN Hardware Manual Download Page 128

Message

Explanation

Recommended Action

Setting Error Toner: #

The indicated print cartridge is
not set correctly, or not set.

Set the indicated print cartridge
correctly.

The error message appears
even though the print cartridge
is set correctly.

Using a dry cloth, carefully
wipe the interface area on the
print cartridge surface.

Reset Tray 1

The indicated paper input tray 1
is not installed correctly, or not
installed.

Install the indicated paper input
tray 1 correctly.

Waste Tnr Bottle Setting Error

There is no waste toner bottle,
or the waste toner bottle is not
installed correctly.

Set the waste toner bottle
correctly.

Service call SCXXX

There is a problem with the
printer's controller.

Turn off the main power, and
then turn it on again.
If the error occurs again,
contact your sales or service
representative.

Density Sensor Require
Cleaning

Color registration failed.

Clean the toner density sensor.
See p.114 "Cleaning the Toner
Density Sensor".

8. Troubleshooting

126

8

Summary of Contents for Aficio SP C240DN













































































































































































Reviews:

No comments