Ricoh Aficio SP C240DN Page 25 Hardware Manual Download | Manualshive

Page: 25 / 172

background image

2. Installing the Printer and Options

This chapter explains how to set up, configure the printer for operation, and install the optional paper
feed unit for this printer.

Installing the Printer

This section describes how to install the printer and perform settings after installation.

Where to Put the Printer

The printer's location should be carefully chosen because environmental conditions greatly affect its
performance.

• The supplied power cord is for use with this equipment only. Do not use with other appliances.

Doing so may result in fire, electric shock, or injury.

• Keep the machine away from flammable liquids, gases, and aerosols. A fire or an electric

shock might occur.

• The wall outlet shall be installed near the machine and shall be easily accessible.

• Connect the machine only to the power source described in this manual. Connect the power

cord directly into a wall outlet and do not use an extension cord. Do not damage, break or
make any modifications to the power cord. Do not place heavy objects on it. Do not pull it hard
nor bend it more than necessary. These actions could cause an electric shock or fire.

• Do not use flammable sprays or solvents in the vicinity of this machine. Doing so could result in

fire or electric shock.

23

2

«
...
23
24
25
26
27
...
»

Summary of Contents for Aficio SP C240DN













































































































































































Reviews:

No comments

Related manuals for Aficio SP C240DN

Brand: Xerox Pages: 93

Brand: Xerox Pages: 36

Copycentre C118

Brand: Xerox Pages: 12

7400DN - Phaser Color LED Printer

Brand: Xerox Pages: 3

Brand: Xerox Pages: 136

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

Brand: Xerox Pages: 8

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 4

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 40

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 38

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 201

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 24

4118P - WorkCentre B/W Laser

Brand: Xerox Pages: 2

3635MFP - Phaser B/W Laser

Brand: Xerox Pages: 212

3300MFP - Phaser B/W Laser

Brand: Xerox Pages: 4

Brand: Xerox Pages: 216

3250D - Phaser B/W Laser Printer

Brand: Xerox Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands