Ricoh Aficio SP C240DN Page 42 Hardware Manual Download | Manualshive

Page: 42 / 172

background image

5.

There are three upright pins on the optional paper feed unit. Align them with the holes on
the underside of the printer, and then carefully lower the printer.

CER005

6.

After installing the option, print the configuration page to confirm the installation.

• When moving the printer, remove the optional paper feed unit.
• Before using the optional paper feed unit, you can make settings in the printer driver.
• If the new device is listed in the column of configuration options, then it has been properly installed.
• If the optional paper feed unit is not installed properly, reinstall it following this procedure. If you

cannot install it properly even after attempting reinstallation, contact your sales or service
representative.

• For printing the configuration page, see Software Guide.
• For loading paper into the paper tray, see p.71 "Loading Paper".
• When adjusting the printing position, see Software Guide.

2. Installing the Printer and Options

40

2

«
...
40
41
42
43
44
...
»

Summary of Contents for Aficio SP C240DN













































































































































































Reviews:

No comments

Related manuals for Aficio SP C240DN

Brand: Tally Pages: 202

Brand: Datamax Pages: 2

Brand: Canon Pages: 358

Brand: Microplex Pages: 135

Brand: Xiamen Hanin Electronic Technology Pages: 62

Brand: Oki Pages: 99

Brand: ioCorp Pages: 18

Brand: MF DIGITAL Pages: 2

Brand: Oce Pages: 186

Brand: EBS Pages: 20

Brand: Citizen Pages: 104

Brand: Infinite Peripherals Pages: 35

Brand: Brother Pages: 378

Brand: Brother Pages: 107

Brand: Brother Pages: 9

PocketJet 3 Plus

Brand: Brother Pages: 11

Brand: Brother Pages: 2

Brand: Brother Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands