manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 8

V

Paper Feed-out mechanism ............................................................. 2-114

2.11  OTHERS............................................................................................. 2-115

2.11.1  SYSTEM CONFIGURATION ..................................................... 2-115
2.11.2  POWER STATES ...................................................................... 2-116

Energy Saver Mode ......................................................................... 2-116
Power-off (Sleep) State.................................................................... 2-116
Main Power Switch Off State ........................................................... 2-117
Power State Transition Diagram ...................................................... 2-117

2.11.3  TOUCH PANEL (A259/A260 MACHINES ONLY)...................... 2-118
2.11.4  BUS SWITCH BOARD (OPTIONAL) ......................................... 2-119

3.  INSTALLATION PROCEDURE ................................................... 3-1

3.1  INSTALLATION REQUIREMENTS .......................................................... 3-1

3.1.1  DIMENSIONS .................................................................................. 3-2
3.1.2  ENVIRONMENTAL REQUIREMENTS ............................................ 3-3
3.1.3  MINIMUM SPACE REQUIREMENTS .............................................. 3-5
3.1.4  POWER REQUIREMENTS.............................................................. 3-6

3.2  COPIER INSTALLATION.......................................................................... 3-7

3.2.1  ACCESSORY CHECK ..................................................................... 3-7
3.2.2  COPIER INSTALLATION PROCEDURE ......................................... 3-8

Tape Removal...................................................................................... 3-8
Removing the Inner Transfer Cover and Paper Transfer
  Locking Screw.................................................................................. 3-10
Developer Installation......................................................................... 3-12
Pressure Release Lever Set-up ......................................................... 3-17
Installing Fusing Silicone Oil .............................................................. 3-18
Initialization and Function Checks...................................................... 3-19
Setting the Tray Paper Size ............................................................... 3-20
Setting the Language and Unit of Measurement ................................ 3-21
Resetting the Counter ........................................................................ 3-21

3.2.2  RELOCATION PROCEDURE........................................................ 3-22

3.3  PAPER TRAY UNIT (A832/A833)........................................................... 3-23

3.3.1  ACCESORY CHECK ..................................................................... 3-23
3.3.2  INSTALLATION ............................................................................. 3-24

TRAY HEATER (OPTION) ................................................................. 3-27

3.4  PLATEN COVER (A749-01) ................................................................... 3-28
3.5  ARDF (A663) .......................................................................................... 3-29

3.5.1  ACCESSORY CHECK ................................................................... 3-29
3.5.2  INSTALLATION ............................................................................. 3-30

3.6  20-BIN SORTER STAPLER (A834)........................................................ 3-31

3.6.1  ACCESSORY CHECK ................................................................... 3-31
3.6.2  INSTALLATION ............................................................................. 3-32

3.7  10-BIN SORTER STAPLER (A555)........................................................ 3-36

3.7.1  ACCESSORY CHECK ................................................................... 3-36
3.7.2  INSTALLATION ............................................................................. 3-37

3.8  3-BIN SORTER (A849) ........................................................................... 3-42

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands