manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 356

24 February, 1999

SYSTEM AND ELECTRONICS

6-85

Replacement

Adjustment

Precautions when replacing the NV-RAM

The NV-RAM stores the counter value and the copier settings.

The procedure for replacing the NV-RAM on the main control board is given below.

Make sure you have the factory settings that come with the copier before beginning
the following procedure:

1.  Print the SP mode values that have been modified from their default values,

using SP7-902.

2.  Turn the main power switch off and unplug the power cord.

3.  Remove the right upper cover [A] (1 screw).

4.  A259/A260 only: Remove the shield plate [B] (3 screws)().

5.  Replace the NV-RAM [C] at IC106 (for A258) or IC104 (for A259/A260) on the

main control board.

6.  Assemble the machine in the reverse order of disassembly.

7.  Turn on the main power and enter the machine's device number in the factory

set mode (consult your executive for details).

8.  Execute SP5-801 (RAM Clear).

9.  Enter the SP mode changes you printed in step 1.

9.  Perform the auto color calibration (ACC) procedure.

10. If the color balance after the ACC is not satisfactory for the customer, adjust the

ACC target using SP4-501 (for copier mode) and SP4-502 (for printer mode),
and/or do the KCMY color balance adjustment.

11. A259/A260: Calibrate the touch panel.

A259R112.WMF

A259I110.WMF

[A]

[B]

[C]

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands