Ricoh Aficio Color 4006 Service Manual Download Page 194

Page: 194 / 487

PAPER TRAY UNIT (A832/A833)

24 February, 1999

3-26

9. Attach the support brackets [A] to the bottom of the paper tray unit as shown (4

screws).

CAUTION

If you do not attach the support brackets, the machine may fall forwards
when the paper trays are pulled open.

10. Pull out the paper tray and load paper into it. (The paper size and direction for

each tray should be designated by the customer.) Position the side and rear
fences properly.

11. Turn on the main switch.

12. Enter the proper paper size for each tray by following the procedure in the

copier’s manual.

13. Attach the appropriate tray decals [B] which are included in the accessory box

with the main copier.

A832I508.WMF

A832I509.WMF

[A]

[B]

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands

Ricoh Aficio Color 4006, Service Manual

Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands