Ricoh Aficio Color 4006 Service Manual Download Page 334

Page: 334 / 487

24 February, 1999

PAPER FEED AND REGISTRATION SECTION

6-63

Replacement

Adjustment

Side-to-side Registration

Standard value: 2

2 mm

1. Enter SP mode 1-2 (side-to-side registration adjustment).

2. Select the paper feed unit to test.

•

Manual feed (by-pass feed table)

•

Tray 1 (Copier paper feed tray): A258 only

•

Tray 2 (Optional paper feed unit, first tray)

•

Tray 3 (Optional paper feed unit, second tray)

•

Tray 4 (Optional paper feed unit, third tray)

•

Duplex

side (Duplex unit): A259/A260 only

NOTE: Any value entered for Tray 1 is ignored in duplex models.

3. Type a number in "Data Input" on the screen at the ten-key pad.

Input value range: -5.0 to 5.0

After entering a number, press the # (Enter key) to save the number in "Set
Data."

To move the image to the right (when viewing towards the direction of paper
feed): Increase the stored value.

To move the image to the left (when viewing towards the direction of paper
feed): Decrease the stored value.

NOTE: To enter a negative number, press the

key before typing the value

of the negative number.

4. Repeat step 3) until the distance [B] in the trim pattern (see the previous page)

falls within the specified range.

NOTE: After the registration adjustment, reset the value of SP5-955-18 to "0" to

resume normal copy operation.

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands

Ricoh Aficio Color 4006, Service Manual

Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands