manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 462

SC CODES

24 February 1999

26

SC

No.

Item

Detection Conditions

Possible Causes

Related

SCs

Troubleshooting Procedure

Type

SC620 ADF

communica-
tion error

- Timing & Condition -
After the main control board
communicates successfully
with the ARDF once, a
communication error is
detected.

•

 Poor 

connection 

or

damaged cable

•

 Defective 

ARDF

main board

•

 Defective 

main

control board

1. Check that the cable is properly connected on the ADF

main board and main control board or check if it is
damaged.

2. Replace the ARDF main board.
3. Replace the main control board.

D

SC621 Sorter

communica-
tion error

- Timing -
Just after the main switch is
turned on or while the sorter is
running
- Condition -
The main control board
detected a communication
error with the sorter main
board.

•

 Poor 

connection 

or

damaged fibre-
optic cable

•

 Defective 

sorter

main board

•

 Defective 

main

control board

1. Check that the fibre-optic cable is properly connected

on the sorter main board and main control board or
check if it is damaged.

2. Replace the sorter main board.
3. Replace the main control board.

D

SC625 FPU

communica-
tion error

- Timing & Condition -
The scanner IPU board
detected a communication
error with the FPU while the
FPU is operating or after the
FPU completes the operation.

•

 Poor 

connection 

or

damaged fibre-
optic cable

•

 Defective 

FPU

main board

•

 Defective 

scanner

IPU board

1. Check that the fibre-optic cable is properly connected

on the FPU main board and main control board or
check if it is damaged.

2. Replace the FPU main board.
3. Replace the scanner IPU board.

B

SC626 Paper tray unit

communica-
tion error

- Timing -
Just after the main switch is
turned on or while the paper
tray unit is running
- Condition -
The main control board
detected a communication
error with the paper tray unit.

•

 Poor 

connection 

or

damaged cables

•

 Defective

CSS/bank interface
board

•

 Defective 

paper

tray unit control
board

•

 Defective 

main

control board

1. Check that the cables are properly connected on the

main control board, CSS/bank interface board, and
paper tray unit control board or check if the cables are
is damaged.

2. Replace CSS/bank interface board.
3. Replace the paper tray unit control board.
4. Replace the main control board.

B

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands