manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 163

DUPLEX TRAY (A259/A260 COPIERS ONLY)

24 February, 1999

2-114

Paper Feed-out mechanism

While paper is stacking in the duplex tray, the paper flatteners [A] correct curl at the
leading edge of the paper.

After all the paper is stacked in the duplex tray, the jogger fences square the paper
and the duplex feed motor turns counter-clockwise briefly to prepare to feed the
paper from the duplex tray. At this time, the bottom plate rises and the duplex feed
rollers [B] move the flip mylars [C] back to the right (front view).

The duplex paper feed system consists of three sets of duplex feed rollers and a
separation roller [D]. The separation roller has a one-way bearing inside, so it
rotates freely during paper stacking and locks during paper feeding. The duplex
feed rollers can feed only the top sheet of the stack because the separation roller
functions in the same way as a friction pad does.

After the duplex tray runs out the final copy, the paper end feeler [E] drops through
a slot in the duplex bottom plate. The duplex paper end actuator [F], which is on
the same shaft as the duplex paper end feeler, pivots into the duplex paper end
sensor [G]. Then the sensor signals the CPU to stop the next paper feed cycle.

A259D651.WMF

A259D647.WMF

[E]

[F]

[G]

[C]

[B]

[B]

[D]

[A]

[A]

[B]

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands