Ricoh Aficio Color 4006 Service Manual Download Page 306

Page: 306 / 487

24 February, 1999

LASER OPTICS SECTION

6-35

Replacement

Adjustment

6.5.1 POLYGON MIRROR MOTOR REPLACEMENT

1. Remove the following covers (see "Covers, Fans, and Filters").

•

Right cover (1 screw)

•

Operation panel (A259/A260: 2 screws, 3 connectors, and 2 grounding wires

A258: 2 screws, 1 connector, and 1 grounding wire [Europe only])

•

Upper rear cover (3 screws)

•

Upper left cover (1 screw)

2. Remove the IC card cover [A] (3 screws).

3. Disconnect 2 connectors [B].

4. A259/A260 only: Remove the shield cover [C] (3 screws).

5. A260 only: Disconnect connector [D] (CN312).

6. Unscrew the scanner clamp screws [E] (4 screws).

7. Remove the support rod [F].

8. Tilt the scanner and set the support rod as shown [G].

CAUTION

Do not remove the support rod while the scanner unit is tilted.
Disengagement of the support bar may cause the scanner unit to fall down.

A259R107.WMF

A259R102.WMF

[A]

[B]

[D]

[F]

[G]

[E]

[C]

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands

Ricoh Aficio Color 4006, Service Manual

Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands