Ricoh Aficio Color 4006 Service Manual Download Page 237

Page: 237 / 487

24 February, 1999

SP MODE ADDITIONAL NOTES

4-9

Service

Tables

4.4.5 5-955-002 TO 5-955-016 LD_PWM (16-GRADATION)

Defines the LD values for the 16 –gradations printed on test patterns SP5-955-018:
5, 16.

002: 1/15 (for the second grade)

003: 2/15 (for the third grade)

004: 3/15 (for the fourth grade)

005: 4/15 (for the fifth grade)

006: 5/15 (for the sixth grade)

007: 6/15 (for the seventh grade)

008: 7/15 (for the eighth grade)

009: 8/15 (for the ninth grade)

010: 9/15 (for the tenth grade)

011: 10/15 (for the eleventh grade)

012: 11/15 (for the twelfth grade)

013: 12/15 (for the thirteenth grade)

014: 13/15 (for the fourteenth grade)

015: 14/15 (for the fifteenth grade)

016: 15/16 (for the sixteenth grade)

4.4.6 5-995-017 LD_PWM (COLOR PATCHES)

Defines the LD value for the color patch at the trailing edge of the test pattern (for
SP5-955-018: 13)

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands

Ricoh Aficio Color 4006, Service Manual

Search results

Summary of Contents for Aficio Color 4006

Reviews:

Brands by name

Popular brands