manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 312

24 February, 1999

DEVELOPMENT UNIT

6-41

Replacement

Adjustment

3.  Remove the left revolver stopper [A] from its storage location on the drawer unit

(1 screw) and fit it into the slot [B] at the rear of the revolver side panel and in
the notch [C] on the drawer unit stay.

ø

CAUTION

If you do not install the revolver stopper before removing the development
unit, the revolver may rotate, causing permanent damage to the
development unit or its holder.

4.  Open the locks [D] at both ends of the development unit [E] (1 screw each) and

remove the development unit [E].

NOTE:  When attaching and detaching the development unit, be sure to turn it in

the direction shown in the diagram. Turning the development unit in the
wrong direction may cause developer to spill from the toner hopper.

ø

CAUTION

Remove the development units one color at a time (never remove two or
more development units from the revolver at the same time). Removing two
or more development units at the same time may upset the balance of the
revolver. This will cause the revolver to revolve by itself, catching, hitting
or trapping your fingers inside the unit.

A259R301.WMF

A259R302.WMF

[A]

[B]

[C]

[D]

[E]

[D]

[A]

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands