manualshive.com logo in svg

Ricoh Aficio Color 4006, Service Manual

Share
Download
Ricoh Aficio Color 4006 Service Manual Download Page 189

24 February, 1999

COPIER INSTALLATION

3-21

Installation

Setting the Language and Unit of Measurement

When the required language is other than English, French, German, Italian and
Spanish, the main program for that language must be downloaded to the main
control board. Then, the desired language can be selected. (Replacement and
Adjustment – System and Electronics - Main Program Downloading)

– SP5-009-001 –

Setting Value

Language

Setting Value

Language

0

Japanese (not
available)

8

Danish

1

English

9

Swedish

2

French

10

Norwegian

3

German

11

Czech

4

Spanish

12

Polish

5

Italian

13

Russian

6

Portuguese

14

Brazilian
Portuguese

7

Dutch

15

Taiwan Chinese

The following procedure outlines how to change the machine language.

1.  Enter SP mode.

2.  Enter SP5-009-001 “Display Language”.

3.  Enter the appropriate value from the above table.

4.  If necessary, change the measurement to either Standard (inches) or Metric

(millimeters) with SP5-009-002.
0: Metric (mm)  1: Standard (inches)
NOTE:  By using SP5-009-002, the display for the unit measurement and the

Enlargement/Reduction ratio shifts.

5.  Turn the machine off/on and check the language and unit measurement on the

LCD.

Resetting the Counter

1.  Enter the SP mode.

2.  Enter SP7-825, "Total Counter 0 Reset."

3.  Quit SP mode and make sure that the counter shows zero using the [Counter]

key on the operation panel.

Summary of Contents for Aficio Color 4006








































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands