manualshive.com logo in svg

Renogy Off-Grid Kit, General Manual

Share
Download
Renogy Off-Grid Kit General Manual Download Page 67

67

 

 

Fig. 8.4

 shows the arrangement for connecting four solar panels in parallel. This arrangement is 

applicable if the solar panels are to be mounted in a 

2x2

 configuration as shown above. Please 

note that the positioning of the junction boxes must be followed for the cables to reach the MC4 
Branch Connectors. This connection requires 

three (3)

 pairs of MC4 Branch Connectors. When 

one or multiple panels are mounted at different locations- that is, separated by a distance, the 
panels must be extended with MC4 Extension Cables (sold separately). 

8.3 Four panels in parallel (12V systems, 1x4 configuration) 
 

 

 

Figure 8.5

 Four RNG-100D Panels in parallel 

 

Fig.  8.5

  above  shows  the  arrangement  for  connecting  four  solar  panels  in  parallel.  This 

arrangement is applicable if the solar panels are to be mounted in a 

1x4

 configuration as shown 

above. For this configuration you will need to purchase 4x1.5’ MC4 Solar Extension Cables. This 
connection requires a 

three (3)

 pairs of MC4 Branch Connectors. When one or multiple panels 

are mounted at different locations- that is, separated by a distance, the panels must be extended 
with MC4 Extension Cables (sold separately). 
 
 
 
 
 
 
 
 
 

Summary of Contents for Off-Grid Kit












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands