background image

OFF

Holding in the lamp key and rotating the channel selector
will raise or lower the frequency by 1 

 increments.

Disables CTCSS or DCS

Selecting the [o] key switches it from OFF to the first
CTCSS tone. Rotate the channel selector to move the
tone frequency up or down in 1 

 increments until the

desired tone frequency is reached. If there isn’t an

asterisk shown next to the last digit of the frequency, then
the increment change is 1 

 if there is an asterisk

shown next to the last digit of the frequency, then the
increment change is 

 Pressing the 

 key will

toggle the increment size between 1 

 and 0.1 Hz.

Selecting the [o] key again switches it from CTCSS to
the first DCS tone. Rotate the channel selector to move
the DCS code up or down until the desired code is
reached. The last alpha character will be an 

 

inverting) or ‘I” (inverting). Pressing the [o] key toggles
the 

 and ‘I”. Pressing the 

 key will toggle the DCS

selection between ‘standard’ and “non-standard’ DCS

codes. If there isn’t an 

asterisk 

shown next to the last

diglt of the DCS code, then the DCS tone selection is

‘standard”; if there is an asterisk shown next to the last

dlgit of the DCS code, then the DCS tone selection is

‘non-standard”. Selecting the 

 key again switches it

from DCS to OFF.

No DTMF or Two Tone signaling on selected channel.

Allows DTMF signaling on selected channel.

Allows Two Tone signaling on selected channel.

Disables this feature.

 
 

SIG OFF

SIG DTMF

SIG TTS

 OFF

  O N

to be transmitted every time the

SCAN DEL

SCAN ADD

 OFF

 ON

SHIFT OFF

SHIFT On

TXPWR H

High power is 5 watts. When set to Hi, pressing the [Lo]
button toggles the power from 5 watts to 1 watt or from 1

 to 5 watts.

Low power is 1 watt. The [Lo] button will not toggle the

channel to high power. Always set to low power.

Receiver 

 is 

 and transmit deviation is

less than 

TXPWR L

WIDE

RELM 

Page 

Summary of Contents for RPU499APIus




























Reviews: