Raven AutoBoom 9600 Installation Manual Download Page 56

Page: 56 / 79

HAPTER

Fast 9600 - 80’-120’ Booms AutoBoom Installation Manual

MOUNT THE AUTOBOOM VALVE

FIGURE 3. AutoBoom Valve Mounting Location

1. Verify that the existing holes in the machine’s center rack (to the left of the machine’s hydraulic valve) align with

the mounting holes in the AutoBoom valve. If they do not, drill two 5/16” holes in the mounting location the

same distance apart as the holes in the AutoBoom valve.

2. Secure the AutoBoom valve (P/N 063-0131-126) to the machine’s center rack using two 5/16”-18 x 1-1/4” hex

bolts (P/N 311-0052-106) and two 5/16” zinc lock washers (P/N 313-1000-019).

Install the Pressure and Tank Hoses

Fitting - 3/4” JIC M/F 45° Swivel Elbow

333-0012-040

Fitting - 9/16” SAE O-Ring Internal Hex Plug

333-0012-104

LV, RV

WARNING

Hydraulics are under pressure. Care should

always be taken with a system that has been

pressurized. When disconnecting or purging

hydraulic hoses, be aware that the hydraulic fluid

within the machine’s system may be extremely

hot and under high pressure.

Fitting

Part Number

Port

Summary of Contents for AutoBoom 9600















































































Search results

Summary of Contents for AutoBoom 9600

Reviews:

Raven AutoBoom 9600, Installation Manual, Page: 56 / 79

Search results

Summary of Contents for AutoBoom 9600

Reviews: