Raven AutoBoom 9600 Installation Manual Download Page 11 | Manualshive

Page: 11 / 79

Raven AutoBoom 9600 Installation Manual Download Page 11

CHAPTER

2

Manual No. 016-0230-096

5

CHAPTER 2

INTRODUCTION

INTRODUCTION

Congratulations on your purchase of the Raven AutoBoom system! This system is designed to provide automated

boom height adjustment for agricultural equipment.

This manual applies to the following machines. For future reference, write your serial number in the space below.

MAKE: Fast

MODEL: 9600 - 80’-100’ Booms

YEAR:

SERIAL NUMBER:

FIGURE 1. Fast 9600

NOTE:

This manual contains the installation instructions for the PowerGlide, PowerGlide Plus, and UltraGlide

systems. Be sure to identify which system you have and follow only the instructions for that system.

PREPARING FOR INSTALLATION

Before installing AutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine
turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.

«
...
9
10
11
12
13
...
»

Summary of Contents for AutoBoom 9600
















































































Reviews:

No comments