manualshive.com logo in svg

Raven AutoBoom 9600, Installation Manual, Page: 27 / 79

Share
Download
Raven AutoBoom 9600 Installation Manual Download Page 27

3

Manual No. 016-0230-096

21

POWERGLIDE

2. Connect the harness cable to the controller cable (P/N 115-0230-002).
3. Tighten the connector cap to secure the connection.

NOTE:

Be sure to allow enough slack in the harness cable to allow for boom racking. If the harness cable is 

not long enough, it may be necessary to connect the 12’ extension cable (P/N 115-0230-008) between 

the harness and controller cables.

CONNECT THE CONTROLLER

FIGURE 10. Controller Connectors

1. Route the controller cable (P/N 115-0230-002) into the right side of the machine’s cab.
2. Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-011).

NOTE:

The AutoBoom controller should be mounted in the machine’s cab so that the machine operator has 

easy access to it.

CONNECT THE POWER LEADS

1. Locate the power cable that has the power and ground leads at one end.
2. Disconnect the machine’s connectors from the battery terminals.
3. Install the power lead on the positive battery terminal and reinstall the machine’s battery connector.
4. Install the ground lead on the negative battery terminal and reinstall the machine’s battery connector.

Summary of Contents for AutoBoom 9600
















































































Reviews:

No comments