Raven AutoBoom 9600 Installation Manual Download Page 15

Page: 15 / 79

CHAPTER

Manual No. 016-0230-096

CHAPTER 3

POWERGLIDE

POWERGLIDE KIT CONTENTS

This section contains a list of the components that are included in the PowerGlide AutoBoom kit. Before beginning

the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have

questions about the kit, contact your Raven dealer.

NOTE:

In addition to the following kit components, an axle kit is required for the operation of the PowerGlide

AutoBoom system. For available kits and ordering information, contact your local Raven dealer.

TABLE 1. PowerGlide Installation Kit (P/N 117-0230-096)

Picture

Item Description

Part Number

Qty.

Not Pictured

Manual - Fast 9600 - 80’-100’ Booms

AutoBoom Installation

016-0230-096

Valve - PowerGlide AutoBoom

016-0131-127

Bracket - Fast Weldment Receiver

116-0159-537

Wheel

322-0131-008

Cable - Boom Sense Adapter

115-0171-546

Cable - 12’ Extension

115-0230-008

Summary of Contents for AutoBoom 9600















































































Search results

Summary of Contents for AutoBoom 9600

Reviews:

Raven AutoBoom 9600, Installation Manual, Page: 15 / 79

Search results

Summary of Contents for AutoBoom 9600

Reviews: