RAMMER RSS05R Operator'S Manual Download Page 44 | Manualshive

Page: 44 / 92

background image

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Page 44 - Lubrication

Carrier hydraulic oil

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,

RSS45R, RSS58R, RSS80R

2. CARRIER HYDRAULIC OIL

2.1 REQUIREMENTS FOR HYDRAULIC OIL

GENERAL REQUIREMENTS

In general, the hydraulic oil originally intended for the carrier can be used with this
product. However, since working with the product heats the oil more than with the
usual excavation work, the temperature of the oil must be monitored.

If the temperature of the hydraulic oil exceeds 80 °C (176 °F), an auxiliary oil cooler
is needed. The oil viscosity must be between 1000-20 cSt while the product is being
used.

When the product is used continuously, the temperature of the hydraulic oil
normalizes at a certain level depending on conditions and on the carrier. The
temperature in the tank must not exceed the maximum allowed.

The product must not be started if the ambient temperature is below freezing and
the oil is very thick. The machine must be moved to bring the oil temperature above
0 °C (32 °F) before working can start (viscosity 1000 cSt or 131 °E).

«
...
42
43
44
45
46
...
»

Summary of Contents for RSS05R





























































































Reviews:

No comments

Related manuals for RSS05R

Brand: Panduit Pages: 44

Brand: Makita Pages: 60

Brand: ABIKOR BINZEL Pages: 56

Brand: OMCN Pages: 13

Brand: WABCO Pages: 24

Brand: Porter-Cable Pages: 15

Brand: Elk Products Pages: 2

Brand: jbc Pages: 72

Brand: Wacker Neuson Pages: 64

Brand: Parker Pages: 136

Brand: X-Tronic Pages: 12

Brand: H&S Pages: 2

Brand: King Canada Pages: 5

Brand: Caillau Pages: 14

Brand: YOKOGAWA Pages: 21

Brand: V-TAC Pages: 13

Brand: Matrix Pages: 46

Brand: M-system Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands