RAMMER RSS05R Operator'S Manual Download Page 25

Page: 25 / 92

Operation - Page 25

Safety

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,
RSS45R, RSS58R, RSS80R

RSS05R, RSS11R, RSS80R

MB010024

FLYING OBJECTS HAZARD

Fragments fly up to 40 m (130 ft)
and could cause death or severe
injury.

Stop operation when a
person enters hazard zone.

Wear approved personal
protective equipment.

169410_ENG-2

IGNORING
INSTRUCTIONS HAZARD

Faulty handling practice could
cause death or severe injury.

Read and follow the instructions
in the operator's manual.

169410_ENG-3

DUST HAZARD

Breathing dust will cause death
or severe injury.

Always wear approved
respirator.

169410_ENG-1

Sandvik Mining and Construction Oy, Taivalkatu 8, 15170 LAHTI, FINLAND

Demolition tool

Manufactured by: MANTOVANIBENNE srl
n° 6, Via Righi - 41037 MIRANDOLA (Mo) ITALY

Serial number

Model

Manufactured

Weight (kg)

Min working
weight (kg)

Max cylinder pressure (bar)

Max rotation pressure (bar)

Max cylinder oil flow (l/min)

Max rotation oil flow (l/min)

Summary of Contents for RSS05R























































































Search results

Summary of Contents for RSS05R

Reviews:

Related manuals for RSS05R

Brands by name

Popular brands

RAMMER RSS05R, Operator'S Manual

Search results

Summary of Contents for RSS05R

Reviews:

Related manuals for RSS05R

Brands by name

Popular brands