RAMMER RSS05R Operator'S Manual Download Page 9 | Manualshive

Page: 9 / 92

background image

Operation - Page 9

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Product introduction

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,
RSS45R, RSS58R, RSS80R

3. PRODUCT INTRODUCTION

3.1 OVERVIEW

The product is a hydraulically operated scrap shear. It can be used on any carrier
which meets the necessary hydraulic and mechanical installation requirements.

3.2 REMOVAL FROM PACKAGE

Remove all the steel belts from the package. Open the package and remove all
plastics covering the product. Recycle all package materials (steel, plastic, wood)
properly.

Check that the product is in good condition and that there is no visible damage.
Check that all ordered parts and accessories have been enclosed with the product.
Some options may be provided by your local dealer, such as installation kits,
including hoses and mounting bracket.

3.3 LIFTING INSTRUCTIONS

Use a hoist when lifting components which weigh 23 kg (51 lb) or more, to avoid
back injury. Make sure all chains, hooks, slings, etc., are in good condition and are
in the correct capacity. Make sure hooks are positioned correctly. Do not side load
the lifting eye during a lifting operation.

PROVIDED LIFTING POINTS

The lifting points located on the product frame are to be used solely to lift or handle
the product itself. The lifting capacity calculation is based on the product's working
weight, including an average sized mounting bracket.

Warning! To avoid falling objects, do not use the product to lift other products.
The lifting points located on the product frame are to be used solely to lift or
handle the product itself.

The maximum allowed total weight is shown on the product's identification plate
and specification page. See “Product specifications” on page 72. If the weight
exceeds the maximum allowed total weight shown on the identification plate and
specification page, you will have to use other lifting points/methods than originally
provided on the product.

«
...
7
8
9
10
11
...
»

Summary of Contents for RSS05R





























































































Reviews:

No comments

Related manuals for RSS05R

Brand: YIHUA Pages: 2

Brand: Valex Pages: 8

Brand: KAKA Industrial Pages: 10

Brand: Lamello Pages: 156

Brand: National Instruments Pages: 8

Brand: K-BUS Pages: 35

Brand: Wacker Neuson Pages: 52

Brand: Senco Pages: 32

Brand: Würth Pages: 8

Brand: Wacker Neuson Pages: 36

Brand: GAMDIAS Pages: 14

Brand: LENCO Pages: 2

Brand: RAMSET Pages: 12

PNEUTORQUE PTM series

Brand: norbar Pages: 26

Brand: Teccpo Pages: 16

Signature DEF Series

Brand: Balcrank Pages: 12

Brand: Glendo Pages: 2

Brand: Delta Elektronika Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands