RAMMER RSS05R Operator'S Manual Download Page 51 | Manualshive

Page: 51 / 92

background image

Maintenance - Page 51

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Routine maintenance

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,
RSS45R, RSS58R, RSS80R

5. Check the clearance of the regulator. See “Adjusting regulator clearance

recovery” on page 59. See “Adjusting regulator lateral guides” on page 61.

6. Check the clearance of the pins. See “Adjusting regulator lateral guides” on

page 61.

WEEKLY MAINTENANCE

1. Check the main body for wear.

2. Check the pins and bushings for wear.

3. Check the cylinder rod, seals and connection points for wear. Tighten if

necessary.

4. Observe hydraulic oil temperature for all lines and connections.

5. Check that the product works smoothly by operating the jaws.

6. Tighten connections, if necessary.

EVERY 40...80 HOURS

Grease the thrust bearing. Adapt the greasing interval and amount of grease to
working conditions.

AFTER FIRST 150 HOURS

Change the oil in the rotation units after the first 150 working hours. See “Changing
oil in the rotation unit” on page 66.

EVERY 2000 HOURS OR ONCE A YEAR

After the first 150 hours oil change, change the oil in the rotation unit every 2000
operating hours, or at least once a year. See “Changing oil in the rotation unit” on
page 66.

1.3 INSPECTION AND MAINTENANCE BY THE DEALER

Note: The times given refer to carrier hours with the product installed.

INITIAL 50 HOUR INSPECTION

It is recommended that your local dealer perform the first inspection after 50 to 100
operating hours. Contact your local dealer for more information about the initial 50-
hour inspection.

«
...
49
50
51
52
53
...
»

Summary of Contents for RSS05R





























































































Reviews:

No comments

Related manuals for RSS05R

Brand: 3M Pages: 11

Brand: Navitar Pages: 6

Brand: Magnaflux Pages: 6

Brand: Oliver Pages: 38

Brand: Gallagher Pages: 104

Brand: jbc Pages: 4

Brand: jbc Pages: 12

Brand: jbc Pages: 8

Brand: jbc Pages: 4

Brand: jbc Pages: 8

Brand: Toku Pages: 7

Brand: Palmgren Pages: 4

Brand: NSI Solutions Pages: 10

Brand: Performance Tool Pages: 6

Brand: Vela Pages: 2

Brand: Ubiquiti Pages: 19

Brand: Draper Pages: 12

Air PoweredRivet Gun

Brand: Campbell Hausfeld Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands