RAMMER RSS05R Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 92

background image

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Page 14 - Operation

Safety

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,

RSS45R, RSS58R, RSS80R

4. SAFETY

4.1 GENERAL SAFETY

All mechanical product can be hazardous if operated without due care or correct
maintenance. Most accidents involving machine operation and maintenance are
caused by failure to observe basic safety rules or precautions. An accident can often
be avoided by recognizing potentially hazardous situations before an accident
occurs.

Because it is impossible to anticipate every possible circumstance that might
involve a potential hazard, the warnings in this guide and on the product are not all
inclusive. If a procedure, tool, working method or operating technique not
specifically recommended by manufacturer is used, you must satisfy yourself that
it is safe for you and others. You should also ensure that the product will not be
damaged or made unsafe by the method of operation or maintenance procedures you
choose.

Safety is not just a matter of responding to the warnings. All the time you are
working with your product you must pay attention to what hazards there might be
and how to avoid them. Do not work with the product until you are sure that you can
control it. Do not start any job until you are sure that you and those around you will
be safe.

Warning! Read the following warning messages carefully. They tell you of
different hazards and how to avoid them. If proper precautions are not taken,
you or others could be seriously injured.

4.2 SAFETY INSTRUCTIONS

MANUALS

Study this manual before installing, operating or maintaining the product. If there is
anything you do not understand, ask your employer or your local dealer to explain
it. Keep this manual clean and in good condition.

The related safety label on the product and the text on the label are shown below.

"IGNORING INSTRUCTIONS HAZARD

Faulty handling practice could cause death or serious injury.

Read and follow the instructions in the operator's manual."

«
...
12
13
14
15
16
...
»

Summary of Contents for RSS05R





























































































Reviews:

No comments

Related manuals for RSS05R

Universal Notebook Power Supply

Brand: Hama Pages: 24

Brand: tacwise Pages: 5

Brand: Xinpu Pages: 12

Central Pneumatic 1/4" Stubby Air Ratchet 91002

Brand: Central Pneumatic Pages: 8

PSI 9000 WR 3U SLAVE

Brand: Elektro-Automatik Pages: 44

Brand: Parkside Pages: 27

Brand: Cleco Pages: 16

Brand: OfiTE Pages: 4

Brand: Parkside Pages: 53

PowerPack PC100

Brand: Waeco Pages: 115

2000-2 LNB Series

Brand: Cross Technologies Pages: 8

Brand: B+K precision Pages: 15

Brand: Kinetik Pages: 8

Bostitch T55 Series

Brand: Stanley Pages: 11

Brand: Senco Pages: 2

Brand: Hellermann Tyton Pages: 8

Invitrogen PowerEase Touch PS0350

Brand: Thermo Scientific Pages: 38

Brand: KMB Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands