RAMMER RSS05R Operator'S Manual Download Page 16 | Manualshive

Page: 16 / 92

background image

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Page 16 - Operation

Safety

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,

RSS45R, RSS58R, RSS80R

COMMUNICATIONS

Bad communications can cause accidents. Keep people around you informed of
what you will be doing. If you will be working with other people, make sure they
understand any hand signals you will be using.

Worksites can be noisy. Do not rely on spoken commands.

WORKSITE

Worksites can be hazardous. Inspect the site before working on it.

Check for potholes, weak ground, hidden rocks, etc. Check for utilities (electric
cables, gas and water pipes, etc.). Mark the positions of cables and pipes.

Poor visibility can cause accidents and damage. Make sure that visibility and
lighting in the working area are adequate.

Worksites can be noisy. Wear ear protection to prevent personal injury.

BANKS AND TRENCHES

Banked material and trenches can collapse. Do not work too close to banks and
trenches where there is a danger of collapse.

SAFETY BARRIERS

Unguarded product in public places can be dangerous. Place barriers around
machinery to keep people away.

AIRBORNE POLLUTANTS

The related safety label on the product and the text on the label are shown below.

"DUST HAZARD

Breathing dust will cause death or severe injury.

Always wear approved respirator."

R010214

«
...
14
15
16
17
18
...
»

Summary of Contents for RSS05R





























































































Reviews:

No comments

Related manuals for RSS05R

Brand: Makita Pages: 20

Brand: Makita Pages: 12

MAKSTAR BTW250 Series

Brand: Makita Pages: 8

Brand: ODA Pages: 113

Brand: Wacker Neuson Pages: 54

Brand: Jet Pages: 20

Brand: Jet Pages: 28

Brand: laguna Pages: 28

Brand: National Flooring Equipment Pages: 14

Brand: N.KO Pages: 13

Brand: Unior Pages: 2

Brand: Unior Pages: 4

Brand: REDSTONE Pages: 70

Brand: Xantrex Pages: 64

Weller Pyropen Jr.

Brand: Cooper Hand Tools Pages: 31

Brand: Airtec Pages: 59

Brand: ICON Pages: 8

Brand: ATI Technologies Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands