RAMMER RSS05R Operator'S Manual Download Page 57

Page: 57 / 92

Maintenance - Page 57

Hardfacing the jaw

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,
RSS45R, RSS58R, RSS80R

3. HARDFACING THE JAW

WELDING TOOLS

HARDFACING CRUSHER JAW

Welding must occur in a workshop with proper welding tools. If you must weld
the product when it is on the carrier, consult your carrier dealer for
precautions during welding.

Warning! Support the jaw to prevent it from closing unexpectedly during
maintenance.

1. Position the product on level ground.

2. Support the jaw.

3. Carefully remove the worn part by carbon arc gouging or by gas cutting at the

base. Note: Connect an earth cable to the part to be repaired.

4. Repair the parent by filling it with a welding rod and finish the surface by

grinding.

5. Preheat hardfacing area to 150 °C... (302 °F)200 °C (392 °F).

Item

Welding tool

Repair of parent

MIG-wire, DIN 8559: SG 2
Welding rod, DIN 1913: E 51 53 B 10

Hardfacing

MIG-wire, DIN 8555: SG 6 - 60
Welding rod, DIN 8555: E 6 - 55

Summary of Contents for RSS05R























































































Search results

Summary of Contents for RSS05R

Reviews:

Related manuals for RSS05R

Brands by name

Popular brands

RAMMER RSS05R, Operator'S Manual

Search results

Summary of Contents for RSS05R

Reviews:

Related manuals for RSS05R

Brands by name

Popular brands