manualshive.com logo in svg

Quanta Cloud Technology QuantaMesh QNOS5, Configuration Manual

Share
Download
Quanta Cloud Technology QuantaMesh QNOS5 Configuration Manual Download Page 88

 

                                                                                                                                                                                                     88 

 

(QCT) (Config-mac-access-list)#exit 

3.  

Configure the destination port as port 0/18. 

(QCT) (Config)#port-monitor session 1 destination interface 0/18 

4.  

Configure the source port as port 0/2. 

(QCT) (Config)#port-monitor session 1 source interface 0/2 

5.  

Enable the port mirroring session. 

(QCT) (Config)#port-monitor session 1 mode 

6.  

To filter L3 traffic so only flows that match the rules in the IP ACL called IPACL are mirrored to the 

destination port, add the IPACL ACL. 

(QCT) (Config)#port-monitor session 1 filter ip access-group IPACL 

7.  

To filter L2 traffic so only flows that match the rules in the MAC-based ACL called MACL are mirrored to 

the destination port, add the MACL ACL. 

(QCT) (Config)#port-monitor session 1 filter mac access-group MACL  

(QCT) (Config)#exit 

Note: 

Both IP ACL and MAC ACL cannot be configured for one session at the same time. 

3.8.

 

Spanning Tree Protocol  

Spanning Tree Protocol (STP) is a layer 2 protocol that provides a tree topology for switches on a bridged 
LAN. STP allows a network to have redundant paths without the risk of network loops. STP uses the 
spanning-tree algorithm to provide a single path between end stations on a network. 

QNOS software supports Classic STP, Multiple STP, and Rapid STP. 

3.8.1.

 

Classic STP, Multiple STP, and Rapdi STP 

Classic STP provides a single path between end stations, avoiding and eliminating loops. Multiple Spanning 
Tree Protocol (MSTP) is specified in IEEE 802.1s and supports multiple instances of Spanning Tree to 
efficiently channel VLAN traffic over different interfaces. Each instance of the Spanning Tree behaves in the 
manner specified in IEEE 802.1w, Rapid Spanning Tree (RSTP), with slight modifications in the working but 
not the end effect (chief among the effects, is the rapid transitioning of the port to Forwarding). The 
difference between the RSTP and the traditional STP (IEEE 802.1D) is the ability to configure and recognize 
full-duplex connectivity and ports which are connected to end stations, resulting in rapid transitioning of 
the port to the Forwarding state and the suppression of Topology Change Notifications. 

MSTP is compatible to both RSTP and STP. It behaves appropriately to STP and RSTP bridges. A MSTP bridge 
can be configured to behave entirely as a RSTP bridge or a STP bridge. 

3.8.2.

 

STP Operation  

Summary of Contents for QuantaMesh QNOS5

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands