manualshive.com logo in svg

Quanta Cloud Technology QuantaMesh QNOS5, Configuration Manual

Share
Download
Quanta Cloud Technology QuantaMesh QNOS5 Configuration Manual Download Page 215

 

                                                                                                                                                                                                     215 

 

SNMP Management  

Only the default router can be managed via SNMP.

 

AAA 

The Authentication, Authorization, and Accounting protocols include services such 
as the RADIUS client and the  client. The switch supports these services 
only on the default router.

 

Network Services  

The Ping and the Trace Route clients are supported in the Virtual Router context. 
Other protocols are supported only in the default router. These include the SNTP 
client, DNS client, sFlow, RPCAP, and Auto Install.

 

Loopback  and  Tunnel 
Interfaces  

Loopback  interfaces  with  IPv4  prefixes  are  supported  in  the  Virtual  Router. 
Loopback  interfaces  with  IPv6  addresses  can  be  configured  only  in  the  default 
router. 

The  number  of  Loopback  interfaces  in  builds  containing  the  VRF  package  is 
increased  to  64.  The  loopback  interfaces  are  shared  across  VR  instances  in  the 
system and there is no restriction on the maximum supported per VR. 

Tunnel interfaces are not supported in the Virtual Router. 

IP 

unnumbered 

interfaces  

IP unnumbered interface cannot be part of non-default VRF instance. This feature 
is supported only in the default router.

 

OSPFv2 

The  OSPFv2  protocol  is  supported  in  the  Virtual  Router.  As  of  the  current 
release, a crash in the OSPFv2 protocol does not cause the switch to reboot. All 
OSPF  features  including  graceful  restart  and  NSF  are  supported  for  OSPFv2  in 
each VR instance.

 

OSPF v3 

The OSPFv3 protocol is supported only in the default router. 

RIP 

RIP is not currently supported in the Virtual Router. 

VRRP 

The Virtual Routing Redundancy Protocol is a fault-tolerance feature that enables 
two or more routers to appear as one router to the IP clients. If one of the VRRP 
routers  fails,  another  router  can  take  over  the  data  forwarding  with  minimum 
interruption to client traffic. 

The VRRP protocol is supported in the Virtual Router context. The VRRP protocol 
enables  two  or  more  virtual  routers  running  on  different  physical  switches  to 
form  a  VRRP  group.  The  Virtual  Routers  running  on  the  same  physical  switch 
cannot form a VRRP group with each other. 

BGP 

The Border Gateway Protocol is intended to be used by the Customer Edge (CE) 
switch  to  communicate  with  other  CE  switches  and  PE  switches  across  the 
Provider  Network.  This  typical  VRF-Lite  deployment  is  described  in  “VRF  Lite 
Deployment  Scenarios”  on  page  274.  The  BGP  protocol  runs  in  the  Default 
Router context and is aware of the Virtual Routers. BGP is used to: 

1.  Redistribute VPN routes from Virtual Routers on the CE switch to the attached 
PE in the Provider Network. 

2.    Leak  routes  dynamically  between  different  Virtual  Routers  on  the  same 
physical switch. This requires support for BGP extended communities and route 

Summary of Contents for QuantaMesh QNOS5

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands