manualshive.com logo in svg

QMS Magicolor WX, User Manual

Share
Download
QMS Magicolor WX User Manual Download Page 236

Notices

QMS magicolor WX User’

’

s Guide

B-8

International Notice

Refer to the “Manufacturer’s Declaration of Conformity Certificate,” 
placed in the printer box, for a full list of the regulatory certifications 
with which this product is in conformity.

Warranty Considerations

Various factors can affect a printer’s warranty. Two important ones are 
consumables and electrostatic discharge. Read your printer warranty 
carefully, and then store it in a safe place. 

»

Note: 

Don't return any merchandise to the manufacturer for service 

without calling for a return merchandise authorization (RMA) number 
before shipping the printer. To get RMA number, in the US call QMS 
Customer Service at 1 (334) 633-1072. If you need replacement 
packaging in which to return the printer for service, in the US call 
QMS National Service at 1 (334) 633-4300 x2530. In other countries, 
refer to appendix A, “QMS Customer Support,” for the telephone 
number of the appropriate QMS office.

Consumables and Your Printer Warranty

The use of non-QMS consumables and/or accessories alone does 
not affect either your warranty or any maintenance contract you may 
have purchased. However, if QMS printer failure or damage is found 
to be directly attributable to the use of non-QMS consumables and/or 
accessories, QMS will not repair the printer free of charge. In this 
case, standard time and material charges will be applied to service 
your printer for that particular failure or damage. QMS recommends 
that you use only QMS consumables and accessories to support your 
printer. To order QMS consumables and accessories in the US, call 
(800) 777-7782. In all other countries, check appendix A, “QMS Cus-
tomer Support,” for the QMS office closest to you.

Electrostatic Discharge and Your Printer Warranty

Electrostatic discharge can destroy circuit boards, such as a SIMM or 
your printer’s controller board. To prevent this, use an anti-static wrist-
band. To use an anti-static wristband, attach one end of it to your wrist 
and the other end to any convenient electrical ground (for example, 

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands