manualshive.com logo in svg

QMS Magicolor WX, User Manual

Share
Download
QMS Magicolor WX User Manual Download Page 181

Repack the 

Printer

6-13

Repacking the Printer

▲

Caution:

 QMS cannot be held responsible for damage to your printer 

during shipment that results from the improper packaging of your 
printer. You must use the instructions given in this document to 
remove the toner cartridges, developer cartridges, and oil bottle; drain 
the fuser unit; replace the pressure-release pieces; remove the OPC 
belt cartridge; and change the waste toner pack before repacking the 
printer in its original shipping box with the original packing materials.

If you need replacement packaging, in the US call QMS National 
Service at 1 (334) 633-4300 x 2530. If you need to return the printer 
for service, in the US call QMS Customer Service at 1 (334) 633-1072 
for an RMA (Return Merchandise Authorization) number before 
shipping the printer. In other countries, refer to appendix A, “QMS 
Customer Support.” 

1

If you have a sheet 
feeder, remove it from 
the printer. Otherwise, 
skip to step 2.

a

Remove the plastic 
brackets from the 
corners of the 
sheet feeder.

(Top View)

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands