manualshive.com logo in svg

QMS Magicolor WX, User Manual

Share
Download
QMS Magicolor WX User Manual Download Page 216

Reseating the 

Drum

QMS magicolor WX User’’'s Guide

7-32

If the Media Jam Message Stays On

n

If a media jam message displays in the control panel message 
window, clear the jam using the appropriate procedure from 
“Clearing Media Jams” on page 7-18. If the message is still there, 
make sure the cassettes have the correct size media, the size key 
slide on the back end of the cassette is set correctly, and all cov-
ers and doors are completely closed. 

n

If the message displays when no jam is evident, make sure the 
media size and type currently in the cassette are selected in the 
printer driver. (See chapter 2, “Printing,” for information on using 
the printer driver.) 

n

As a last resort, try turning the printer off and on (this will cause 
jobs to be lost).

Reseating the Drum

If 

ENGINE ERROR E9

 displays in the control panel message window, 

use the following procedure to reseat the drum:

1

Open the back cover of the printer.

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands