background image

1

Chapter 1: Introduction

About This Manual, below

Product Overview (page 2)

WebPAM Software (page 3)

Key Features and Benefits (page 3)

Specifications (page 5)

Thank you for purchasing one of Promise Technology’s FastTrak TX4310 RAID 
Controller card.

About This Manual

This 

User Manual

 describes how to setup, use and maintain the FastTrak 

TX4310 RAID Controller card.

This manual includes a full table of contents, chapter task lists and numerous 
cross-references to help you find the specific information you are looking for. 

Also included are four levels of notices:

      

Note

Note

 provides helpful information such as hints or alternative 

ways of doing a task.

Important

An 

Important

 calls attention to an essential step or point required 

to complete a task. Important items include things often missed. 

Caution

Caution

 informs you of possible equipment damage or loss of 

data and how to avoid them.

Warning

Warning

 notifies you of probable equipment damage or loss of 

data, or the possibility of physical injury, and how to avoid them.

Summary of Contents for FastTrak TX4310







































































































































Reviews: