manualshive.com logo in svg

Promise Technology FastTrak TX4310, User Manual

Share
Download
Promise Technology FastTrak TX4310 User Manual Download Page 17

Chapter 2: Installation

9

2.

Remove the inside slot cover of an available 32-bit PCI slot on the 
motherboard.Install the FastTrak Serial ATA RAID card into the open PCI 
slot. Secure the bracket to the system's frame.

3.

Attach your system case's 2- or 4-pin LED cable to the LED connector on the 
FastTrak card (see 

Install the Disk Drives

, below).

4.

Fasten the controller card bracket to the system case.

Install the Disk Drives 

The FastTrak TX4310 RAID Controller card supports only Serial ATA disk drives. 
For optimal performance, install disk drives of the same model and capacity. The 
drives’ matched performance allows the logical drive to function better as a single 
drive. 

The table above shows the number of drives required for each RAID level. If you 
plan to create a mirror (RAID 1) for protection, you can use two new drives OR 
use an existing drive and a new drive. The new drive must be the same size or 
larger than the existing drive.

1.

Install the disk drives into the disk drive bays of your system. 

Important

If you wish to include your current bootable Serial ATA drive using 
the Windows operating system as part of a bootable Mirrored 
(RAID 1) logical drive on your FastTrak card, do NOT connect the 
disk drive to the FastTrak yet. You MUST install the Windows 
driver software first onto this drive while it is still attached to your 
existing disk drive controller. 

Level

 Number of Drives

RAID 0

any number

RAID 1

2 only

RAID 5

3 or 4

RAID 10

4 only

JBOD

any number

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands