Promise Technology FastTrak TX4310 User Manual Download

Page: 40 / 134

FastTrak TX4310 User Manual

hot spare drive, the logical drive will rebuild automatically. You must identify
and replace the failed disk drive.

Offline

– The logical drive is no longer operational and the FastBuild utility

cannot rebuild it. You must identify and replace the failed drive(s). Then you
can create a new logical drive and copy your data to it from the last tape
backup or other device.

For RAID levels 1, 5 and 10, at least two or more disk drives in the logical
drive have failed.

For a RAID 0 or JBOD logical drive, at least one disk drive has failed.

Main Menu

When the FastTrak BIOS displays on your computer screen, press Ctrl-F to
launch the FastBuild utility and display the Main Menu.

The Main Menu (above) has five options:

•

Press 1 to view disk drive assignments

•

Press 2 to create a logical drive or view information about an existing logical
drive.

•

Press 3 to delete a logical drive.

•

Press 4 to view and change controller configuration.

•

Press Esc (Escape) to exit the menu.

Summary of Contents for FastTrak TX4310







































































































































Search results

Summary of Contents for FastTrak TX4310

Reviews:

Related manuals for FastTrak TX4310

Brands by name

Popular brands

Promise Technology FastTrak TX4310, User Manual

Search results

Summary of Contents for FastTrak TX4310

Reviews:

Related manuals for FastTrak TX4310

Brands by name

Popular brands