manualshive.com logo in svg

Promise Technology FastTrak TX4310, User Manual

Share
Download
Promise Technology FastTrak TX4310 User Manual Download Page 31

23

Chapter 3: Install Drivers

•

Make a Driver Installation Diskette, page 24

•

Windows Server 2003
•

New, page 25

•

Exsting, page 26

•

Confirm, page 26

•

Windows  XP
•

New, page 27

•

Exsting, page 28

•

Confirm, page 28

•

Windows 2000
•

New, page 29

•

Exsting, page 30

•

Confirm, page 30

Following are driver installation procedures for the Windows operating systems 
that support the FastTrak TX4310 RAID Controller card. The FastTrak drivers for 
Windows are included on the CD.

Drivers and installation instructions for Linux are downloadable from the Promise 
website at www.promise.com.

Important

If you wish to include your current bootable drive using the 
Windows 2000, XP or Server 2003 operating system as part of a 
bootable Mirrored (RAID 1) disk array, you MUST install the 
FastTrak driver to this drive while it is still attached to your existing 
disk drive controller.

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands