manualshive.com logo in svg

Promise Technology FastTrak TX4310, User Manual

Share
Download
Promise Technology FastTrak TX4310 User Manual Download Page 41

Chapter 4: FastBuild™ Utility

33

View Drive Assignments

From the Main Menu screen, press 1 to see the View Drive Assignments screen 
(below). 

This screen reports disk drive assigments and provides the following information:

Channel: ID

 – Shows the FastTrak Controller channel ID (1 through 4) to which a 

particular disk drive is attached. 

Drive Mode

l – Identifies the manufacturer, model, and model number (if 

applicable) of each disk drive. 

Capacity (MB)

 – Reflects the capacity in MB (megabytes) of the disk drive. 

Assignment

  – This field identifies the logical drive to which the disk drive 

belongs. In the example above, there is one logical drive composed of three disk 
drives. LD 1-2 means logical drive 1, disk drive 2.

Unassigned drives are labeled 

free

 and are considered 

hot spares

 to provide 

fault tolerance. Unassigned drives may also be used to create a new logical drive 
at any time.

Extent  

– An extent is a portion of the disk drive. The FastTrak TX4310 RAID 

Controller card allows you to split the capacity of a disk drives between two 
logical drives. The portion of a disk drive available to be used in a logical drive is 
called an 

extent

. The extent, or sum of two extents, is slightly smaller than the 

total capacity of the disk drive.

See “View Drive Assignments, Split Disk Drives” on page 38 for an example of 
two extents for each disk drive.

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands