Promise Technology FastTrak TX4310 User Manual Download | Manualshive

Page: 35 / 134

background image

Chapter 3: Install Drivers

27

Windows XP

New Installation

The following details the installation of the FastTrak TX4310 RAID Controller
drivers while installing Windows XP.

1.

Start the installation:
•

Floppy Install: Boot the computer with the Windows XP installation
diskettes.

•

CD-ROM Install: Boot from the CD-ROM. Press F6 after the message
"Press F6 if you need to install third party SCSI or RAID driver" appears.

2.

When the Windows XP Setup window is generated, press S to specify an
Additional Device(s).

3.

Insert the FastTrak driver diskette into drive A: and press Enter.

4.

Choose

Windows Promise FastTrak TX4310 (tm) Controller

from the list that

appears on screen, and then press the Enter.

5.

Press S to use the driver on the floppy disk and then press Enter to continue
with installation.

6.

The Windows XP Setup screen will appear again saying “Setup will load
support for the following mass storage devices:” The list will include
“Windows Promise FastTrak TX4310 (tm) Controller”.
NOTE: If there are any additional devices to be installed, specify them now.
When all devices are specified, continue to the next step.

7.

From the Windows XP Setup screen, press the Enter. Setup will now load all
device files and then continue the Windows XP installation.

«
...
33
34
35
36
37
...
»

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Related manuals for FastTrak TX4310

SKU 4670PE31GDT

Brand: Diamond Multimedia Pages: 1

Brand: Kogan Pages: 1

Brand: ATCOM Pages: 15

Waveterminal 2496

Brand: ESI Pages: 38

Brand: Baltech Pages: 5

Raptor DL–Lite

Brand: Eizo Pages: 2

Brand: StarTech.com Pages: 11

Brand: S4A Pages: 2

Brand: Sonnet Pages: 2

Brand: EMS Imaging Pages: 8

Brand: ADLINK Technology Pages: 44

Brand: Encore Pages: 2

Brand: Diablotek Pages: 1

Brand: Media Vision Pages: 50

Brand: US Robotics Pages: 2

9800GT 512MB GREEN EDITION

Brand: Gainward Pages: 2

7.1 SOUND CARD PCI ADAPTER

Brand: Icidu Pages: 6

Brand: 3Dlabs Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands