manualshive.com logo in svg

Promise Technology FastTrak TX4310, User Manual

Share
Download
Promise Technology FastTrak TX4310 User Manual Download Page 83

Chapter 5: WebPAM

75

Logical Drive Migration and Expansion

The Logical Drive–Migration tab enables you to migrate or expand a logical drive. 
Migration is the process of changing the RAID level of an existing logical drive. 
Expansion is the process of adding more physical drives to a logical drive while 
keeping the same RAID level. 

The Migration feature applies to certain combinations of RAID level and number 
of physical drives, as described in the table below. 

The Expansion feature applies only to RAID 0 and RAID 5 logical drives. You can 
add physical drives to a logical drive, up to eight drives, the maximum number 
supported by the FastTrak controller.

Migration and Expansion are not available for JBOD.

For more information, see “Logical Drive Expansion” on page 104 and “RAID 
Level Migration” on page 105.

You can set up an Migration to begin immediately (on demand) or schedule a 
Migration for a time when there is less demand on the RAID system. 

On Demand

To migrate a logical drive:

1.

Click on the Logical Drive View 

 icon in Tree View.

2.

Click on the Logical Drive 

 icon of the logical drive you want to migrate.

3.

Click on the Migration tab in Management View.

From

To

Result

RAID 0: 1 or 2 drives

RAID 5: 3 or 4 drives

Increased performance 
and capacity, adds 
redundancy

RAID 10: 4 drives

RAID 0: 3 drives

RAID 5: 4 drives

Increased performance 
and capacity, adds 
redundancy

RAID 1: 2 drives

RAID 5: 3 or 4 drives

Increased performance 
and capacity

RAID 10: 4 drives

RAID 10: 4 drives

RAID 5: 4 drives

Increased capacity

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands