manualshive.com logo in svg

Promise Technology FastTrak TX4310, User Manual

Share
Download
Promise Technology FastTrak TX4310 User Manual Download Page 46

FastTrak TX4310 User Manual

38

View Drive Assignments, Split Disk Drives

After you create two logical drives from the same set of disk drives, press 1 on 
the Main Menu screen to see the View Drive Assignments screen (below). 

In this example, observe how each of the disk drives in Channels 1, 2 and 3 are 
split between two logical drives. Extent 1 belongs to logical drive 1 (LD 1). Extent 
2 belongs to logical drive 2 (LD 2).

Under Assignment,  the disk drive is divided into LD 1 and LD 2. For example, LD 
1-2 means logical drive 1, disk drive 2. LD 2-3 means logical drive 2, disk drive 3.

Note that the combined size of the extents is slightly smaller than the total 
capacity of the disk drive.

Unassigned drives are labeled 

free

 and are considered 

hot spares

 to provide 

fault tolerance in the event of a disk drive failure. Alternatively, you can use an 
unassigned drive to create a new logical drive.

Summary of Contents for FastTrak TX4310







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands