background image

- 64 -

0600_GB-Power-Control_8537

GB

POWEr COnTrOL - OPErATiOn

Note!

Optical alarm: 

blinking indicator

Acoustic alarm: 

intermittent tone

The alarms will only 

become active at 

a speed of 1 km/h

blinkend

blinkend

Alarms

-  Monitoring  will  only  become  active  when  the  seed 

monitor registers speed.

-  If an activated monitor reacts then a corresponding 

alarm will respond.
-  An optical (blinking indicator) and acoustic alarm 

(intermittent tone)

•  Pressing the keys below shows the alarm report in total 

display.
-  With the instruction “Erase” the intermittent tone is 

suppressed (press key F1). 

-  The optical remains however. 

-  The acoustic alarm becomes active again if relaying 

of the driving lane through the driving lane sensor 
occurs, that is after driving through a U-turn.

-  Return to the main menu with the ESC key

Seed shaft alarm

The  seed  shaft  rotation  is  checked  through  the  seed 
shaft sensor. 

-  If  the  seed  monitor  registers  no  impulses  within 

the pre-programmed time, an optical and acoustic 
alarm is triggered.

•  Pressing the “F2” key below shows the alarm report 

in total display.
=  Seed shaft monitor: Seed shaft at standstill
-  ERASE (see above)

Level alarm

If  seed  level  falls  below  a  minimum  level  in  the  seed 
container, an optical and acoustic alarm is triggered.

•  Pressing the “F” key below shows the alarm report 

in total display
=  Level monitor: Seed container is empty

-  ERASE (see above)

Summary of Contents for VITASEM A 251



















































































Reviews: