Pottinger VITASEM A 251 Operator'S Manual Download

Page: 55 / 82

- 55 -

0600_GB-Power-Control_8537

POWEr COnTrOL - OPErATiOn

Main menu

• Press

“MAIN” key

- The actual control status is shown on the display.

1.1

Driving lane cycle

• Relaying the driving lane cycle occurs automatically

through a sensor.

• However the driving lane cycle can also be relayed

manually.

Press “Increase driving lane cycle by 1”

key

- The driving lane cycle increases by 1 every time the

key is pressed

- When driving lane cycle and driving lane rhythm are

in phase, the driving lane is put down.

- The “driving lane” (= Fahrgasse) stroke will then

appear inverted on the display

• The automatic relaying of the driving lane cycle can

also be interrupted.

Press “Lock/release driving lane counter”

key

- The actual driving lane cycle value is now clearly

shown

- The automatic driving lane relay sensor and “key

7” are locked

- If “key 8” is pressed the automatic relay is reactivated

and the value for the driving lane cycle is shown in
large scale again.

1.2

Driving lane rhythm

- A symmetrical driving lane is shown without index

(see diagram above)

- An asymmetrical driving lane is shown with index

“A”

- Nothing appears in the indicator field when driving

lane is deactivated (Driving lane off)

- For special driving lanes the relative driving lane

rhythm is shown in the indicator field

For further information on setting the driving lane rhythm
see section “Driving lane switch”

Reference surface hectare meter

- Displays the actual status

For further information see section “Hectare meter”

1.5

Drive speed

- Displays the actual drive speed

1.7

Seed shaft monitor

- Graphic data display of actual status

= Rotating shaft

= Shaft at stand still

- If only the lower graphic data function key is

actuated, extensive information is displayed (see
section “Alarms”)

- Press ESC to return to main menu.

1.8

Level monitor

- Graphic data display of actual status

= Seed container empty

= Seed container full

- Bar indicator between 0 and 100%
- If only the lower graphic data function key is

actuated, extensive information is displayed (see
section “Alarms”)

- Press ESC to return to main menu.

Note!

The main menu can

be exited in the

following ways:

Use the keys

Note!

For further

information on

the respective

monitoring

functions see

the section

“Monitoring

Functions”

1.1

1.2

1.7

1.5

1.8

Summary of Contents for VITASEM A 251



















































































Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands

Pottinger VITASEM A 251, Operator'S Manual

Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands