PoolPak ComPak AW 0550 Installation, Operation And Maintenance Manual Download Page 30

Page: 30 / 92

www.poolpak.com | 800-959-7725

| ComPak

Series - Installation, Operation and Maintenance

Handling

All units are shipped completely assembled. Care should be taken to avoid damage due to rough handling.

If the unit is not to be immediately installed, it must be protected from weather and site hazards.

For ComPak rigging, refer to the generic or job specific product drawing in the Technical Product Library.

For RoofComPak rigging, see

Figure 4-2.

Figure 4-2. RP Lift Views

LIFT VIEW

RP WITH INT ACC & GAS HEAT

UNIT WEIGHT: 3,700 LBS

SPREADER BAR

LENGTH 50" (2X)

LIFT VIEW

RP WITH INT GAS HEAT ONLY

UNIT WEIGHT: 2,900 LBS

SPREADER BAR LENGTH

50" THREE PLACES

Summary of Contents for ComPak AW 0550



























































































Search results

Summary of Contents for ComPak AW 0550

Reviews:

Related manuals for ComPak AW 0550

Brands by name

Popular brands

PoolPak ComPak AW 0550, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for ComPak AW 0550

Reviews:

Related manuals for ComPak AW 0550

Brands by name

Popular brands