Additional information
14
127
En
HDMI
You can’t get i.LINK to display
when using the
SIGNAL SEL
button.
• Make sure your i.LINK source components are switched on.
• Check that i.LINK is assigned correctly (see
The Input Setup menu
on page 101).
After upgrading a component, it
is not recognized and cannot be
selected using the i.LINK
connection.
• You may need to reset the i.LINK database memory in the receiver (use the front panel):
1 In the standby mode, press
STANDBY/ON
while pressing
SETUP
.
2 Use
/
to select
i.LINK DB [NO]
, then press
ENTER
.
3 Use
/
to select
Clear
, then press
ENTER
.
4 When
Clear? [OK]
appears, press
ENTER
again. Resetting is completed once the normal screen
appears. If
DB ERROR
is displayed, perform the procedure again.
Symptom
Remedy
Symptom
Remedy
The HDMI indicator blinks
continuously.
• Check all the points below.
No picture or sound.
• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-Video or composite video jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver (even
if it is HDCP-compatible). In this case, connect using the component, S-Video or composite video jacks
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or plasma display, try adjusting the resolution, DeepColor or
other setting for your component.
• If ‘
NOT SUPPORT
’ appears in the receiver’s display, try adjusting the resolution, DeepColor or other
setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to THROUGH, you
cannot hear audio output from all channels. In this case, make a digital or analog audio connection.
• To output signals in DeepColor, use an HDMI cable (High Speed HDMI™ Cable) to connect this receiver
to a component or TV with the DeepColor feature.
No picture.
• Try changing the Resolution setting (in
Setting the Video options
on page 108).
• Set the HDMI output setting to the connected HDMI OUT terminal (in
Switching the HDMI output
on
page 110).
No sound, or sound suddenly
ceases.
• Check that the HDMI AV setting is set to
AMP/THROUGH
.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
Noisy or distorted picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-Video or composite), then start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
HDCP ERROR
shows in the
display.
• Check whether or not the connected component is compatible with HDCP. If it is not compatible with
HDCP, reconnect the source device using a different type of connection (component, S-Video or
composite). Some components that are compatible with HDCP still cause this message to be displayed, but
so long as there is no problem with displaying video, this is not a malfunction.
Amp-linked operation not
possible using HDMI control
function.
• Select
ON
for the HDMI control setting (see
Setting the HDMI Control mode
on page 99).
• Turn the TV’s power on before turning on this receiver’s power.
• Set the TV side HDMI control setting to
ON
.
• Connect the TV to the
HDMI OUT 1
terminal and set the HDMI output to
HDMI OUT 1
. Then turn on first
the TV’s power, then this receiver’s power.
SC_09TX.book Page 127 Monday, November 26, 2007 10:32 PM
Summary of Contents for SC-09TX - Elite AV Network Receiver
Page 1: ...uctions REC ...
Page 160: ......